1/10 Scale Ambulance

This is the building forum for the Combat Boat 90. If you are interested in the STL's for this project, they are available to those who help me by contributing 15 Euro. Then you get access to a sub-forum where STL's, instructions and mods are located.

kv for the main motors. (I am planning on running 6s)

1050kv 4084 motor with water cooling. Link: https://hobbyking.com/en_us/turnigy-aqu ... motor.html
3
100%
2200kv 3974 motor with water cooling. Link:https://hobbyking.com/en_us/turnigy-aqu ... motor.html
0
No votes
 
Total votes: 3

Mazzarin
Posts: 10
Joined: Wed Jun 20, 2018 7:13 pm

1/10 Scale Ambulance

Postby Mazzarin » Thu May 23, 2019 6:53 pm

First parts printed!

I began with the Jet inlets and nozzles, Now i have begun Printing the hull.
untitled.png
untitled.png (78.4 KiB) Viewed 14378 times
Attachments
IMG_20190522_221909.jpg
IMG_20190522_221909.jpg (2.43 MiB) Viewed 14378 times

Mazzarin
Posts: 10
Joined: Wed Jun 20, 2018 7:13 pm

Re: 1/10 Scale Ambulance

Postby Mazzarin » Thu May 23, 2019 6:57 pm

My dad was the commander on this boat for 8 years and did Close to 2000 missions with it.
Last edited by Mazzarin on Thu May 23, 2019 7:32 pm, edited 1 time in total.

admin
Site Admin
Posts: 429
Joined: Thu Jan 11, 2018 7:46 pm

Re: 1/10 Scale Ambulance

Postby admin » Sat May 25, 2019 10:32 am

Nice! Can't wait to see this one! :D

Matsa
Posts: 32
Joined: Tue May 22, 2018 10:46 am

Re: 1/10 Scale Ambulance

Postby Matsa » Mon Jun 03, 2019 6:13 am

More pics please! ;)

Matsa...

Mazzarin
Posts: 10
Joined: Wed Jun 20, 2018 7:13 pm

Re: 1/10 Scale Ambulance

Postby Mazzarin » Mon Jun 03, 2019 5:01 pm

Matsa wrote:
Mon Jun 03, 2019 6:13 am
More pics please! ;)

Matsa...
Haha sure! coming now!

Mazzarin
Posts: 10
Joined: Wed Jun 20, 2018 7:13 pm

Re: 1/10 Scale Ambulance

Postby Mazzarin » Mon Jun 03, 2019 5:07 pm

now i have printed essentially all parts for the jet drives! I had to reprint them because i used orange filament at the time and messed up the paint job :lol: Now they turned out Fantastic! tomorrow i am buying more filamet to start the next hull pieces!

I am not entirely sure about what seal and bearings i want to use, my current idea is to use theese parts:

https://www.kullager.se/product.html/ra ... ory_id=293
https://www.kullager.se/product.html/ku ... ory_id=115

The motors i planned on using sold out in the available warehouse so they sadly will have to wait

I will update as things progress!
Attachments
IMG_20190603_185833.jpg
IMG_20190603_185833.jpg (1.82 MiB) Viewed 14283 times
IMG_20190603_185820.jpg
IMG_20190603_185820.jpg (1.81 MiB) Viewed 14283 times


Who is online

Users browsing this forum: No registered users and 1 guest